The Code of Federal Regulations of the United States of AmericaU.S. Government Printing Office, 1976 The Code of Federal Regulations is the codification of the general and permanent rules published in the Federal Register by the executive departments and agencies of the Federal Government. |
No grāmatas satura
1.–5. rezultāts no 100.
79. lappuse
... diameter with posts spaced not more than 8 feet on centers . ( iii ) For structural steel railings , posts and top ... diameter ; when of metal pipe , at least 11⁄2 inches in diameter . The length of brackets shall be such as will give a ...
... diameter with posts spaced not more than 8 feet on centers . ( iii ) For structural steel railings , posts and top ... diameter ; when of metal pipe , at least 11⁄2 inches in diameter . The length of brackets shall be such as will give a ...
82. lappuse
... diameter , are permitted on the wide face provided they are at least one - half inch back from either edge and not more frequent than 1 to any 3 feet of ladder length . ( iii ) Pitch and bark pockets are per- mitted provided they are ...
... diameter , are permitted on the wide face provided they are at least one - half inch back from either edge and not more frequent than 1 to any 3 feet of ladder length . ( iii ) Pitch and bark pockets are per- mitted provided they are ...
83. lappuse
... Diameter of hole board for rung ( d shall be taken as not less than 0.67 ) . ( iii ) Adjustment of sizes for wood parts of stepladders and other ladder types covered by this section may be made as follows : ( a ) The dimensions ...
... Diameter of hole board for rung ( d shall be taken as not less than 0.67 ) . ( iii ) Adjustment of sizes for wood parts of stepladders and other ladder types covered by this section may be made as follows : ( a ) The dimensions ...
84. lappuse
... diameter with standard commer- cial tolerances , which shall pass through metal washers of sufficient thickness and diameter on each end to prevent press- ing - into the side rails , and a truss block which shall be fitted between the ...
... diameter with standard commer- cial tolerances , which shall pass through metal washers of sufficient thickness and diameter on each end to prevent press- ing - into the side rails , and a truss block which shall be fitted between the ...
85. lappuse
... diameter with standard commercial tolerances which shall pass through metal washers of sufficient thickness and diameter on each end to prevent pressing into the side rails , and a truss block shall be fitted between the truss rod and ...
... diameter with standard commercial tolerances which shall pass through metal washers of sufficient thickness and diameter on each end to prevent pressing into the side rails , and a truss block shall be fitted between the truss rod and ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
3,3'-Dichlorobenzidine Abrasive Wheels accordance acetylene American National Standard ammonium nitrate ANSI apply approved Assistant Secretary belt Benzidine building capacity check valve clean Code Compressed Gas Association connections constructed containers covered crane cylinders designed diameter discharge electrical employees equipment exceed explosives exposure extinguishers feet fire flammable floor fusible plug gage graph ground guard handling hazard hoisting hood horizontal hose inches inspection installed laboratory ladder least less liquefied petroleum gas load located LP-Gas machine material maximum means ment metal methyl minimum NFPA operation OSHA oxygen paragraph piping platform portable pressure Pressure Vessel prevent protection quired rated regulated area relief valve rope safe Safety and Health safety relief devices scaffold side rails sling specific spray storage subdivision subparagraph Subpart surface Table tainers tank tion trucks vapor vehicle vent ventilation vertical vided welding wheels width wire wire rope
Populāri fragmenti
25. lappuse - Each employer — (1) shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees; (2) shall comply with occupational safety and health standards promulgated under this Act.
29. lappuse - Administrator issued under section 14; (3) to discharge or in any other manner discriminate against any employee because such employee has filed any complaint or instituted or caused to be instituted any proceeding under or related to this Act, or has testified or is about to testify in any such proceeding or has served or is about to serve on an industry committee...
11. lappuse - ... to the extent feasible, on the basis of the best available evidence, that no employee will suffer material impairment of health or functional capacity even if such employee has regular exposure to the hazard dealt with by such standard for the period of his working life.
51. lappuse - Should it appear from the affidavits of a party opposing the motion that he cannot for reasons stated present by affidavit facts essential to justify his opposition, the court may refuse the application for judgment or may order a continuance to permit affidavits to be obtained or depositions to be taken or discovery to be had or may make such other order as is just.
26. lappuse - ... inspect and investigate during regular working hours and at other reasonable times, and within reasonable limits and in a reasonable manner, any such place of employment and all pertinent conditions, structures, machines, apparatus, devices, equipment, and materials therein, and to question privately any such employer, owner, operator, agent or employee.
28. lappuse - Whoever, being an officer or employee of the United States or of any department or agency thereof, publishes, divulges, discloses, or makes known in any manner or to any extent not authorized by law any information coming to him in the course of his employment or official duties or by reason of any examination or investigation made by, or return, report or record made to or filed with, such department or agency or officer or employee thereof, which information concerns or relates to the trade secrets,...
66. lappuse - commerce" means trade, traffic, commerce, transportation, transmission, or communication among the several States; or between a State and any place outside thereof; or within the District of Columbia, or a possession of the United States ; or between points in the same State but through a point outside thereof. "(h) The term "industry affecting commerce...
29. lappuse - ... and a copy shall be provided the employer or his agent no later than at the time of inspection, except that, upon the request of the person giving such notice, his name and the names of individual employees referred to therein shall not appear in such copy or on any record published, released, or made available pursuant to subsection (g) of this section.
44. lappuse - ... is unable to comply with a standard by its effective date because of unavailability of professional or technical personnel or of materials and equipment needed to come into compliance with the standard or because necessary construction or alteration of facilities cannot be completed by the effective date...
164. lappuse - Survey" means an evaluation of the radiation hazards incident to the production, use, release, disposal, or presence of radioactive materials or other sources of radiation under a specific set of conditions. When appropriate, such evaluation includes a physical survey of the location of materials and equipment, and measurements of levels of radiation or concentrations of radioactive material present.