Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 10.
3-8. lappuse
... wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight . Maintenance Action Reference Tighten . Replace if missing . Tell your supervisor ...
... wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight . Maintenance Action Reference Tighten . Replace if missing . Tell your supervisor ...
3-12. lappuse
... wire seals ( 9 ) are installed . Separate input shaft ( 10 ) from junction box assembly ( 11 ) . Check that input shaft ( 10 ) of superelevation box assembly ( 12 ) turns freely without binding . Connect input shaft ( 10 ) to junction ...
... wire seals ( 9 ) are installed . Separate input shaft ( 10 ) from junction box assembly ( 11 ) . Check that input shaft ( 10 ) of superelevation box assembly ( 12 ) turns freely without binding . Connect input shaft ( 10 ) to junction ...
4-12. lappuse
... wire seal ( 6 ) from adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) . Using pry bar , pry bracket ( 9 ) from turret pad while rotating adjuster ( 7 ) using 1-1 / 16 " open wrench ...
... wire seal ( 6 ) from adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) . Using pry bar , pry bracket ( 9 ) from turret pad while rotating adjuster ( 7 ) using 1-1 / 16 " open wrench ...
4-17. lappuse
... Wire cutter tool Lockwire tool 1/4 ′′ reamer SUPPLIES : Cleaning rag Alcohol ( item 1 , App A ) or solvent ( item 4 , App A ) PERSONNEL : Three Repairman A : Holds ballistics drive Repairman B : Installs hardware Repairman C : Helps in ...
... Wire cutter tool Lockwire tool 1/4 ′′ reamer SUPPLIES : Cleaning rag Alcohol ( item 1 , App A ) or solvent ( item 4 , App A ) PERSONNEL : Three Repairman A : Holds ballistics drive Repairman B : Installs hardware Repairman C : Helps in ...
4-28. lappuse
... wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open end wrench , loosen two screws ( 8 ) and ( 9 ) . 5 . Using 1 1/4 " open end wrench , turn adjuster arm ( 10 ) until fire control level ( 6 ) bubble is centered . 6 . Using 15/16 ...
... wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open end wrench , loosen two screws ( 8 ) and ( 9 ) . 5 . Using 1 1/4 " open end wrench , turn adjuster arm ( 10 ) until fire control level ( 6 ) bubble is centered . 6 . Using 15/16 ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint