Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 7.
2-1. lappuse
... : Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
... : Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
3-1. lappuse
... vehicle , except for inspection items marked with an asterisk ( * ) . These items can be checked properly only with ballistics drive or subcomponents removed from vehicle . NOTE Once the ballistics drive is removed from vehicle DS / GS ...
... vehicle , except for inspection items marked with an asterisk ( * ) . These items can be checked properly only with ballistics drive or subcomponents removed from vehicle . NOTE Once the ballistics drive is removed from vehicle DS / GS ...
3-12. lappuse
... vehicle . Send ballistics drive to depot for repair . Para 4-6 Para 4-5 , frame 3 , steps 3 and 7 and frame 7 , steps 3 and 7 and frame 12 steps 2 and 6 Para 4-4 , frame 5 , step 1 . Para 4-5 , frame 8 , step 2 . 3-12 Vol II TM 9-1220 ...
... vehicle . Send ballistics drive to depot for repair . Para 4-6 Para 4-5 , frame 3 , steps 3 and 7 and frame 7 , steps 3 and 7 and frame 12 steps 2 and 6 Para 4-4 , frame 5 , step 1 . Para 4-5 , frame 8 , step 2 . 3-12 Vol II TM 9-1220 ...
4-3. lappuse
... Vehicle parked , vehicle MASTER SWITCH off , gun level PRELIMINARY PROCEDURES : For ballistics drive M10 , M10A1 , M10A3 , and M10A6 remove M13 series elevation quadrant ( TM 20-2 ) Remove M32 ( or M35 ) gunner's periscope ( TM 20-2 ) ...
... Vehicle parked , vehicle MASTER SWITCH off , gun level PRELIMINARY PROCEDURES : For ballistics drive M10 , M10A1 , M10A3 , and M10A6 remove M13 series elevation quadrant ( TM 20-2 ) Remove M32 ( or M35 ) gunner's periscope ( TM 20-2 ) ...
4-4. lappuse
... vehicle . Clamp assembly ( 8 ) is not part of ballistics drive . Remove clamp assembly ( 8 ) with limit stop attached . 5 . GO TO FRAME 2 Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) 1 2 4-4 Vol II TM 9-1220-220-34.
... vehicle . Clamp assembly ( 8 ) is not part of ballistics drive . Remove clamp assembly ( 8 ) with limit stop attached . 5 . GO TO FRAME 2 Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) 1 2 4-4 Vol II TM 9-1220-220-34.
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint