Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 11.
2-1. lappuse
... CONDITION : Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
... CONDITION : Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
2-10. lappuse
... tube ( 3 ) ( outside of tank at notches ) to form crosshairs . Use tape or strap ( 4 ) to hold thread ( 2 ) in place ( TM 10 ) . ( Thread must be tight ) . Using range finder ( 5 ) , find a target about 1200 meters away . WARNING Do not ...
... tube ( 3 ) ( outside of tank at notches ) to form crosshairs . Use tape or strap ( 4 ) to hold thread ( 2 ) in place ( TM 10 ) . ( Thread must be tight ) . Using range finder ( 5 ) , find a target about 1200 meters away . WARNING Do not ...
4-20. lappuse
... tube at maximum elevation to prevent injury and to provide easier access to component . Repairman A , position adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench ...
... tube at maximum elevation to prevent injury and to provide easier access to component . Repairman A , position adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench ...
4-22. lappuse
... tube at maximum elevation to prevent injury and to provide easier access to component . Repairman A , position adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench ...
... tube at maximum elevation to prevent injury and to provide easier access to component . Repairman A , position adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench ...
4-37. lappuse
... tube ( 5 ) until rangefinder level vial bubble ( 1 ) is centered . 5 . Using 3/4 " open end wrench , tighten two screws ( 3 ) and ( 4 ) . 6 . Using lockwire tool , install new lockwire ( 2 ) ( JPG ) . GO TO FRAME 13 01 2 3 NOT SHOWN Ο ...
... tube ( 5 ) until rangefinder level vial bubble ( 1 ) is centered . 5 . Using 3/4 " open end wrench , tighten two screws ( 3 ) and ( 4 ) . 6 . Using lockwire tool , install new lockwire ( 2 ) ( JPG ) . GO TO FRAME 13 01 2 3 NOT SHOWN Ο ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint