Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.5. rezultāts no 7.
2-10. lappuse
... tight ) . Using range finder ( 5 ) , find a target about 1200 meters away . WARNING Do not set circuit breaker switch ( 1 ) to ON until all personnel and equipment are out of the way of gun movement . Set circuit breaker switch ( 1 ) to ...
... tight ) . Using range finder ( 5 ) , find a target about 1200 meters away . WARNING Do not set circuit breaker switch ( 1 ) to ON until all personnel and equipment are out of the way of gun movement . Set circuit breaker switch ( 1 ) to ...
3-2. lappuse
... tight . 8 . Check that five pins ( three Replace if missing . pins for M10A3 ) ( 6 ) are not missing . 9 . Check two rubber covers ( one rubber cover for Replace universal joint if damaged . M10A3 ) ( 7 ) on universal joints ( 8 ) for ...
... tight . 8 . Check that five pins ( three Replace if missing . pins for M10A3 ) ( 6 ) are not missing . 9 . Check two rubber covers ( one rubber cover for Replace universal joint if damaged . M10A3 ) ( 7 ) on universal joints ( 8 ) for ...
3-4. lappuse
... tight . Using 5/64 ′′ Allen wrench , Tighten . Replace if missing . 4 . Tighten . Replace if missing check that three setscrews ( 6 ) are tight . GO TO FRAME 3 Para 3-2 Cont 3-2 . BALLISTICS DRIVE INSPECTION UPON RECEIPT ( CONT ) 3-4 ...
... tight . Using 5/64 ′′ Allen wrench , Tighten . Replace if missing . 4 . Tighten . Replace if missing check that three setscrews ( 6 ) are tight . GO TO FRAME 3 Para 3-2 Cont 3-2 . BALLISTICS DRIVE INSPECTION UPON RECEIPT ( CONT ) 3-4 ...
3-6. lappuse
... tight . Using 1/2 " open end wrench , check that eight screws ( 7 ) are tight . Using 5/16 " square stock , 1 " long , with 3/8 " socket and extension and rachet , check that two plugs ( 8 ) are tight . Tighten plug . Tighten . Replace ...
... tight . Using 1/2 " open end wrench , check that eight screws ( 7 ) are tight . Using 5/16 " square stock , 1 " long , with 3/8 " socket and extension and rachet , check that two plugs ( 8 ) are tight . Tighten plug . Tighten . Replace ...
3-8. lappuse
... tight . Check that electrical wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight . Maintenance Action Reference Tighten . Replace if ...
... tight . Check that electrical wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight . Maintenance Action Reference Tighten . Replace if ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint