Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 10.
2-1. lappuse
... thread Tape or strap Pencil Paper Binoculars PERSONNEL : Two REFERENCES : TM 10 Series manuals for removing and installing firing mechanism of gun , M60 , M60A1 TM 9-2350-215-0 and TM 9-2350-260-10 , M60A3 TM 9-2350-253-10 , M60A1 ...
... thread Tape or strap Pencil Paper Binoculars PERSONNEL : Two REFERENCES : TM 10 Series manuals for removing and installing firing mechanism of gun , M60 , M60A1 TM 9-2350-215-0 and TM 9-2350-260-10 , M60A3 TM 9-2350-253-10 , M60A1 ...
2-10. lappuse
... thread ( 2 ) over gun tube ( 3 ) ( outside of tank at notches ) to form crosshairs . Use tape or strap ( 4 ) to hold thread ( 2 ) in place ( TM 10 ) . ( Thread must be tight ) . Using range finder ( 5 ) , find a target about 1200 meters ...
... thread ( 2 ) over gun tube ( 3 ) ( outside of tank at notches ) to form crosshairs . Use tape or strap ( 4 ) to hold thread ( 2 ) in place ( TM 10 ) . ( Thread must be tight ) . Using range finder ( 5 ) , find a target about 1200 meters ...
4-20. lappuse
... threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) onto turret mounting pad ( 1 ) . Make sure pin holes in bracket ( 5 ) are lined ...
... threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) onto turret mounting pad ( 1 ) . Make sure pin holes in bracket ( 5 ) are lined ...
4-22. lappuse
... threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) onto turret mounting pad ( 1 ) . Make sure pin holes in bracket ( 5 ) are lined ...
... threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) onto turret mounting pad ( 1 ) . Make sure pin holes in bracket ( 5 ) are lined ...
4-42. lappuse
... thread) the number of turns recorded during removal procedure. 2. Using wrench, tighten capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined surface as shown. Slide pin (7) through lugs (4 and ...
... thread) the number of turns recorded during removal procedure. 2. Using wrench, tighten capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined surface as shown. Slide pin (7) through lugs (4 and ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint