Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 11.
iii. lappuse
... Temperature Compensating Rod .... Temperature Compensating Rod Maintenance Procedures Index . ... Temperature Compensating Rod Removal Temperature Compensating Rod Installation . 4-5 4-17 4-40 4-6 4-40 4-7 4-41 ... 4-8 4-42 Section 4 ...
... Temperature Compensating Rod .... Temperature Compensating Rod Maintenance Procedures Index . ... Temperature Compensating Rod Removal Temperature Compensating Rod Installation . 4-5 4-17 4-40 4-6 4-40 4-7 4-41 ... 4-8 4-42 Section 4 ...
2-20. lappuse
... temperature compensating rod with a rod mounting bracket which bolts to a pad inside the turret wall . The drive also has a superelevation box assembly and level vial . TABULATED DATA 1-4 . Data M10 M10A1 M10A3 M10A4 M10A5 M10A6 Length ...
... temperature compensating rod with a rod mounting bracket which bolts to a pad inside the turret wall . The drive also has a superelevation box assembly and level vial . TABULATED DATA 1-4 . Data M10 M10A1 M10A3 M10A4 M10A5 M10A6 Length ...
4-1. lappuse
... Temperature Compensating Rod Trunnion Link 123 4-3 4-6 4-9 Drive Connector 4 4-12 Link Connector Fire Control Level 5 6 4-15 4-18 Light Assembly 7 4-21 Rangefinder Link Connector Assembly 8 4-26 Junction Box Assembly 9 4-29 Shaft and ...
... Temperature Compensating Rod Trunnion Link 123 4-3 4-6 4-9 Drive Connector 4 4-12 Link Connector Fire Control Level 5 6 4-15 4-18 Light Assembly 7 4-21 Rangefinder Link Connector Assembly 8 4-26 Junction Box Assembly 9 4-29 Shaft and ...
4-12. lappuse
... temperature compensating rod ( 4 ) to turret pad . Using 3/4 " open wrench , loosen two screws ( 5 ) and remove wire seal ( 6 ) from adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) ...
... temperature compensating rod ( 4 ) to turret pad . Using 3/4 " open wrench , loosen two screws ( 5 ) and remove wire seal ( 6 ) from adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) ...
4-24. lappuse
... temperature compensating rod bracket ( 1 ) to turret mounting pad on turret wall with two screws ( 2 ) and ( 3 ) , two lockwashers ( 4 ) , and two flat washers ( 5 ) . 2 . Using torque wrench , tighten screw ( 2 ) to 5 foot - pounds ...
... temperature compensating rod bracket ( 1 ) to turret mounting pad on turret wall with two screws ( 2 ) and ( 3 ) , two lockwashers ( 4 ) , and two flat washers ( 5 ) . 2 . Using torque wrench , tighten screw ( 2 ) to 5 foot - pounds ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint