Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.5. rezultāts no 78.
7. lappuse
... Retainer Coating Thickness The maximum operating life of the bearings tested was 14.9 hours , obtained with bearing ... retainer showed that the lead coating had worn through in the ball pockets and at the inner locating diameter . After ...
... Retainer Coating Thickness The maximum operating life of the bearings tested was 14.9 hours , obtained with bearing ... retainer showed that the lead coating had worn through in the ball pockets and at the inner locating diameter . After ...
16. lappuse
... retainer materials lubricated the bearings reasonably well , the best overall performance was achieved with this retainer material . This conclusion is based on the consistently low bearing torque values for this material . Post - Test ...
... retainer materials lubricated the bearings reasonably well , the best overall performance was achieved with this retainer material . This conclusion is based on the consistently low bearing torque values for this material . Post - Test ...
13. lappuse
... retainer testing , and adhesive wear had begun on the balls and races in places where the gold was lost . Of the 13 tests run , only five pairs of bearings lasted more than 100 hours and the maximum life obtained was 369 hours . Greater ...
... retainer testing , and adhesive wear had begun on the balls and races in places where the gold was lost . Of the 13 tests run , only five pairs of bearings lasted more than 100 hours and the maximum life obtained was 369 hours . Greater ...
19. lappuse
... retainer , percent 1.2 .8 .4 Retainer O 13 - S 16 - S 14 - S Δ 23 - S 15 - S a 22 - S 4 20 - S Δ 21 - S ( a ) Retainer material , laminated glass cloth with PTFE binder . ( b ) Retainer material , glass - fiber - molybdenum disulfide ...
... retainer , percent 1.2 .8 .4 Retainer O 13 - S 16 - S 14 - S Δ 23 - S 15 - S a 22 - S 4 20 - S Δ 21 - S ( a ) Retainer material , laminated glass cloth with PTFE binder . ( b ) Retainer material , glass - fiber - molybdenum disulfide ...
18. lappuse
... retainer wear , sliding distance of the retainer at the inner race , and postrun conditions of the bearings are given in table IV . Inner race . - · Profile traces were made of the inner - race grooves to indicate the postrun condition ...
... retainer wear , sliding distance of the retainer at the inner race , and postrun conditions of the bearings are given in table IV . Inner race . - · Profile traces were made of the inner - race grooves to indicate the postrun condition ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint