Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 6.
4-28. lappuse
... mark ( 3 ) is lined up with qualifying mark ( 4 ) on bearing cap ( 5 ) , tighten four screws ( 11 ) . Look and see if fire control ( 6 ) bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire ...
... mark ( 3 ) is lined up with qualifying mark ( 4 ) on bearing cap ( 5 ) , tighten four screws ( 11 ) . Look and see if fire control ( 6 ) bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire ...
4-29. lappuse
... BALLISTICS DRIVE INSTALLATION ( CONT ) 2 1 4 ( 11 ) VIEW FROM OTHER SIDE WRENCH 9 6 SLOT 10 8 7 5 QUALIFICATION MARK ON EACH BEARING CAP Para 4-5 Cont 4-5 . FRAME 8 Step BALLISTICS DRIVE INSTALLATION ( CONT. Vol II 4-29 TM 9-1220-220-34.
... BALLISTICS DRIVE INSTALLATION ( CONT ) 2 1 4 ( 11 ) VIEW FROM OTHER SIDE WRENCH 9 6 SLOT 10 8 7 5 QUALIFICATION MARK ON EACH BEARING CAP Para 4-5 Cont 4-5 . FRAME 8 Step BALLISTICS DRIVE INSTALLATION ( CONT. Vol II 4-29 TM 9-1220-220-34.
4-30. lappuse
... mark on output shaft ( 1 ) with index mark on qualification plate ( 2 ) . 3 . Set electronic computer to " zero " elevation . 4 . 5 . Using 3/16 " flat tip screwdriver , install shaft ( 3 ) on superelevation box output shaft ( 1 ) with ...
... mark on output shaft ( 1 ) with index mark on qualification plate ( 2 ) . 3 . Set electronic computer to " zero " elevation . 4 . 5 . Using 3/16 " flat tip screwdriver , install shaft ( 3 ) on superelevation box output shaft ( 1 ) with ...
4-68. lappuse
... marks on cross shaft ( 2 ) . 23 2. Place clamp ( 3 ) inside marks on cross shaft ( 2 ) . 3 . Align mounting holes of light assembly ( 1 ) and clamp ( 3 ) . 4 . Place four cap screws ( 4 ) into mounting holes ( 4 ) . 5 . Holding cap ...
... marks on cross shaft ( 2 ) . 23 2. Place clamp ( 3 ) inside marks on cross shaft ( 2 ) . 3 . Align mounting holes of light assembly ( 1 ) and clamp ( 3 ) . 4 . Place four cap screws ( 4 ) into mounting holes ( 4 ) . 5 . Holding cap ...
4-70. lappuse
... mark the position of the rear connector assembly ( 1 ) on tube assembly ( 2 ) . 1 . 2 . Cut lead wire seal ( 3 ) . 3 . Using 3/4 " wrench , loosen capscrews ( 4 ) . 4 . Holding tube assembly ( 2 ) turn rear connector assembly ( 1 ) ...
... mark the position of the rear connector assembly ( 1 ) on tube assembly ( 2 ) . 1 . 2 . Cut lead wire seal ( 3 ) . 3 . Using 3/4 " wrench , loosen capscrews ( 4 ) . 4 . Holding tube assembly ( 2 ) turn rear connector assembly ( 1 ) ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint