Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.5. rezultāts no 8.
v. lappuse
... listing by paragraph number and page number Performance Test ( Vol I , Chap 2 ) Maintenance Task Index ( Vol II , App B ) which lists major assemblies , subassemblies and paragraph numbers of all maintenance procedures Before doing ...
... listing by paragraph number and page number Performance Test ( Vol I , Chap 2 ) Maintenance Task Index ( Vol II , App B ) which lists major assemblies , subassemblies and paragraph numbers of all maintenance procedures Before doing ...
13. lappuse
... LISTED BON DA FORM 2404 THAT MAY AFFECT PERFORMANCE TEST CHECK FAULT SYMPTOM INDEX ( VOL I , CHAP 3 ) AND DO DO MAINTENANCE ( VOL II , CHAP 4 ) OR FAULT ISOLATION ( VOL I , CHAP 4 ) TO CORRECT FAULT SYMPTOM . DO PERFORMANCE TEST ( VOLI ...
... LISTED BON DA FORM 2404 THAT MAY AFFECT PERFORMANCE TEST CHECK FAULT SYMPTOM INDEX ( VOL I , CHAP 3 ) AND DO DO MAINTENANCE ( VOL II , CHAP 4 ) OR FAULT ISOLATION ( VOL I , CHAP 4 ) TO CORRECT FAULT SYMPTOM . DO PERFORMANCE TEST ( VOLI ...
2-16. lappuse
... listed on DA Form 2404 . Do final inspection ( Vol II , para 5-2 ) . END OF TASK Para 2-2 Cont a . Replace lamp ( TM 20-2 ) b . Disassemble light as- sembly and check for worn , corroded , or broken parts and re- place ( Vol II , para 4 ...
... listed on DA Form 2404 . Do final inspection ( Vol II , para 5-2 ) . END OF TASK Para 2-2 Cont a . Replace lamp ( TM 20-2 ) b . Disassemble light as- sembly and check for worn , corroded , or broken parts and re- place ( Vol II , para 4 ...
2-20. lappuse
... listed on DA Form 2404 before any repairs are made . c . Chapter 4 , Maintenance Procedures , gives step - by - step procedures to repair faults found during inspection of troubleshooting . d . Chapter 5 , Final Inspection , gives ...
... listed on DA Form 2404 before any repairs are made . c . Chapter 4 , Maintenance Procedures , gives step - by - step procedures to repair faults found during inspection of troubleshooting . d . Chapter 5 , Final Inspection , gives ...
3-1. lappuse
... listed on DA Form 2404 before taking any maintenance actions . The performance test in Volume I , Chapter 2 , should be done after doing the inspection upon receipt . 3-2 . BALLISTICS DRIVE INSPECTION UPON RECEIPT TOOLS : 1/4 " , 3/16 ...
... listed on DA Form 2404 before taking any maintenance actions . The performance test in Volume I , Chapter 2 , should be done after doing the inspection upon receipt . 3-2 . BALLISTICS DRIVE INSPECTION UPON RECEIPT TOOLS : 1/4 " , 3/16 ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint