Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 8.
2-8. lappuse
... housing window ( 2 ) of Symptom Maintenance Action range finder ( 3 ) , turn range knob ( 4 ) until range scale reads 500 meters . 3 . While looking into range finder eyepiece ( 5 ) , set circuit breaker switch ( 1 ) to ON . Check that ...
... housing window ( 2 ) of Symptom Maintenance Action range finder ( 3 ) , turn range knob ( 4 ) until range scale reads 500 meters . 3 . While looking into range finder eyepiece ( 5 ) , set circuit breaker switch ( 1 ) to ON . Check that ...
2-16. lappuse
... housing ( 2 ) . 2 . Using multimeter , check that Faulty light assembly . resistance between housing ( 2 ) and plug ( 3 ) is 6 + .5 ohms . 3 . Install connector ( 1 ) in light assembly housing ( 2 ) . NOTE FOLLOW - ON MAINTENANCE ...
... housing ( 2 ) . 2 . Using multimeter , check that Faulty light assembly . resistance between housing ( 2 ) and plug ( 3 ) is 6 + .5 ohms . 3 . Install connector ( 1 ) in light assembly housing ( 2 ) . NOTE FOLLOW - ON MAINTENANCE ...
4-57. lappuse
... housing ( 2 ) . 2. Position cover ( 3 ) on housing ( 2 ) and hold in place while installing level ( 4 ) . 3 . Place eccentric ( 5 ) into threaded ring ( 6 ) . 4 . Using spanner wrench , install threaded ring ( 6 ) with eccentric ( 5 ) ...
... housing ( 2 ) . 2. Position cover ( 3 ) on housing ( 2 ) and hold in place while installing level ( 4 ) . 3 . Place eccentric ( 5 ) into threaded ring ( 6 ) . 4 . Using spanner wrench , install threaded ring ( 6 ) with eccentric ( 5 ) ...
4-62. lappuse
... housing ( 4 ) and gasket ( 5 ) from mount ( 3 ) . Using flat tip screwdriver , remove screw ( 6 ) and lock washer ( 7 ) holding terminal ( 8 ) to housing ( 4 ) . 4 . Remove terminal ( 8 ) from housing ( 4 ) . 5 . Using open end wrench ...
... housing ( 4 ) and gasket ( 5 ) from mount ( 3 ) . Using flat tip screwdriver , remove screw ( 6 ) and lock washer ( 7 ) holding terminal ( 8 ) to housing ( 4 ) . 4 . Remove terminal ( 8 ) from housing ( 4 ) . 5 . Using open end wrench ...
4-64. lappuse
... housing ( 3 ) . 2 . Pull light socket ( 4 ) out of housing ( 3 ) . 3 . Turn lens ( 5 ) counterclockwise and remove from light socket ( 4 ) . 4 . Remove lamp ( 6 ) from light socket ( 4 ) . 5 . Tag two wires ( 7 ) ( JPG ) . 6 . Using ...
... housing ( 3 ) . 2 . Pull light socket ( 4 ) out of housing ( 3 ) . 3 . Turn lens ( 5 ) counterclockwise and remove from light socket ( 4 ) . 4 . Remove lamp ( 6 ) from light socket ( 4 ) . 5 . Tag two wires ( 7 ) ( JPG ) . 6 . Using ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint