Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.5. rezultāts no 7.
4-6. lappuse
... holding cap ( 5 ) to range finder ( 2 ) . Remove rear connector assembly ( 1 ) from range finder ( 2 ) . 3. Replace cap ( 5 ) , four lockwashers ( 4 ) and four screws ( 3 ) on range finder ( 2 ) and hand tighten to prevent loss . GO TO ...
... holding cap ( 5 ) to range finder ( 2 ) . Remove rear connector assembly ( 1 ) from range finder ( 2 ) . 3. Replace cap ( 5 ) , four lockwashers ( 4 ) and four screws ( 3 ) on range finder ( 2 ) and hand tighten to prevent loss . GO TO ...
4-7. lappuse
... holding cap ( 4 ) to superelevation box assembly ( 5 ) . 2 . Repairman A : remove connector assembly ( 1 ) . 3. Replace cap ( 4 ) , four lockwashers ( 3 ) , and four screws ( 2 ) on superelevation box assembly ( 5 ) and hand tighten to ...
... holding cap ( 4 ) to superelevation box assembly ( 5 ) . 2 . Repairman A : remove connector assembly ( 1 ) . 3. Replace cap ( 4 ) , four lockwashers ( 3 ) , and four screws ( 2 ) on superelevation box assembly ( 5 ) and hand tighten to ...
4-10. lappuse
... holding cap ( 3 ) to left support ( 4 ) . Repairman A : hold trunnion link ( 5 ) . Repairman B : using 1/2 " box end wrench , remove two screws ( 6 ) and two lockwashers ( 7 ) holding cap ( 8 ) to left support ( 4 ) . 3 . Repairman B ...
... holding cap ( 3 ) to left support ( 4 ) . Repairman A : hold trunnion link ( 5 ) . Repairman B : using 1/2 " box end wrench , remove two screws ( 6 ) and two lockwashers ( 7 ) holding cap ( 8 ) to left support ( 4 ) . 3 . Repairman B ...
4-34. lappuse
... holding cap ( 3 ) to superelevation box ( 4 ) . Repairman A : hold rangefinder link connector assembly ( 5 ) . Repairman B : using 1/2 ′′ box end wrench , install link connector assembly ( 5 ) to superelevation box ( 4 ) with cap ( 3 ) ...
... holding cap ( 3 ) to superelevation box ( 4 ) . Repairman A : hold rangefinder link connector assembly ( 5 ) . Repairman B : using 1/2 ′′ box end wrench , install link connector assembly ( 5 ) to superelevation box ( 4 ) with cap ( 3 ) ...
4-35. lappuse
... holding cap ( 3 ) to range finder ( 4 ) . Using 1/2 " box end wrench , hold link connector assembly ( 5 ) in socket ( 4 ) and install lockwashers ( 2 ) , screws ( 1 ) and caps ( 3 ) to rangefinder ( 4 ) . 3 . Remove wooden block . GO TO ...
... holding cap ( 3 ) to range finder ( 4 ) . Using 1/2 " box end wrench , hold link connector assembly ( 5 ) in socket ( 4 ) and install lockwashers ( 2 ) , screws ( 1 ) and caps ( 3 ) to rangefinder ( 4 ) . 3 . Remove wooden block . GO TO ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint