Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 11.
4-6. lappuse
... four lockwashers ( 4 ) and four screws ( 3 ) on range finder ( 2 ) and hand tighten to prevent loss . GO TO FRAME 3 01 ב 1 WOODEN BLOCK ON TOP OF RANGE FINDER 2 Para 4-4 Cont 2 5 1 3 1 : N 4-4 . FRAME 3 Step 1 . 4-6 Vol II TM 9-1220-220-34.
... four lockwashers ( 4 ) and four screws ( 3 ) on range finder ( 2 ) and hand tighten to prevent loss . GO TO FRAME 3 01 ב 1 WOODEN BLOCK ON TOP OF RANGE FINDER 2 Para 4-4 Cont 2 5 1 3 1 : N 4-4 . FRAME 3 Step 1 . 4-6 Vol II TM 9-1220-220-34.
4-7. lappuse
... ( 4 ) , four lockwashers ( 3 ) , and four screws ( 2 ) on superelevation box assembly ( 5 ) and hand tighten to prevent loss . GO TO FRAME 4 3 2 1 5 WOODEN BLOCK Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) FRAME 5. Vol II 4-7 TM 9- ...
... ( 4 ) , four lockwashers ( 3 ) , and four screws ( 2 ) on superelevation box assembly ( 5 ) and hand tighten to prevent loss . GO TO FRAME 4 3 2 1 5 WOODEN BLOCK Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) FRAME 5. Vol II 4-7 TM 9- ...
4-8. lappuse
... 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) FRAME 5 Step Procedure 1 . 2 . Using 3/16 " flat tip screwdriver , remove four screws ( 1 ) and four lockwashers ( 2 ) . Place superelevation drive shaft ( 3 ) out of the way . 3 . 4 . Replace four ...
... 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) FRAME 5 Step Procedure 1 . 2 . Using 3/16 " flat tip screwdriver , remove four screws ( 1 ) and four lockwashers ( 2 ) . Place superelevation drive shaft ( 3 ) out of the way . 3 . 4 . Replace four ...
4-9. lappuse
... four lockwashers ( 2 ) . Using 3/16 " flat tip screwdriver , remove four screws ( 3 ) and four lockwashers ( 4 ) . Remove shaft assembly ( 5 ) . Place four lockwashers ( 2 ) and four screws ( 1 ) in shaft hub ( 6 ) and hand tighten to ...
... four lockwashers ( 2 ) . Using 3/16 " flat tip screwdriver , remove four screws ( 3 ) and four lockwashers ( 4 ) . Remove shaft assembly ( 5 ) . Place four lockwashers ( 2 ) and four screws ( 1 ) in shaft hub ( 6 ) and hand tighten to ...
4-10. lappuse
... nut ( 12 ) and lockwasher ( 13 ) holding trunnion link ( 5 ) to trunnion arm ( 14 ) . 7 . Repairman A : remove trunnion link ( 5 ) by tapping with hammer . 8 . Replace two caps ( 3 and 8 ) four lockwashers ( 2 and 7 ) and four screws ...
... nut ( 12 ) and lockwasher ( 13 ) holding trunnion link ( 5 ) to trunnion arm ( 14 ) . 7 . Repairman A : remove trunnion link ( 5 ) by tapping with hammer . 8 . Replace two caps ( 3 and 8 ) four lockwashers ( 2 and 7 ) and four screws ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint