Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 6.
4-46. lappuse
... flatwasher ( 8 ) . Carefully press out seal ( 9 ) , bearings ( 10 ) , seals ( 11 and 12 ) , and stud ( 13 ) . Discard seals if damaged . 6 . Remove disks ( 14 ) by tightening setscrews ( 3 ) , using .050 allen wrench . 7 . Discard disks ...
... flatwasher ( 8 ) . Carefully press out seal ( 9 ) , bearings ( 10 ) , seals ( 11 and 12 ) , and stud ( 13 ) . Discard seals if damaged . 6 . Remove disks ( 14 ) by tightening setscrews ( 3 ) , using .050 allen wrench . 7 . Discard disks ...
4-48. lappuse
... flat washer ( 6 ) , lockwasher ( 7 ) , and cap screw ( 8 ) . 3 . Install pillow block cap ( 9 ) on connector ( 10 ) , using 2 3/16 pin spanner wrench . 4 . Install disks ( 11 ) and setscrews ( 12 ) , using .050 allen wrench . 5 ...
... flat washer ( 6 ) , lockwasher ( 7 ) , and cap screw ( 8 ) . 3 . Install pillow block cap ( 9 ) on connector ( 10 ) , using 2 3/16 pin spanner wrench . 4 . Install disks ( 11 ) and setscrews ( 12 ) , using .050 allen wrench . 5 ...
4-50. lappuse
... flat washer ( 4 ) , seal ( 5 ) , and retainer ( 6 ) from connector ( 7 ) using 2 3/16 pin spanner wrench . Press seal ( 5 ) and washer ( 4 ) out of retainer ( 6 ) . Discard seal and washer if damaged . Carefully press out sleeve ( 8 ) ...
... flat washer ( 4 ) , seal ( 5 ) , and retainer ( 6 ) from connector ( 7 ) using 2 3/16 pin spanner wrench . Press seal ( 5 ) and washer ( 4 ) out of retainer ( 6 ) . Discard seal and washer if damaged . Carefully press out sleeve ( 8 ) ...
4-52. lappuse
... flat washer ( 5 ) , seal ( 6 ) , retainer ( 3 ) , bearing ( 7 ) , and sleeve ( 8 ) . 3 . Install disks ( 9 ) and setscrews ( 10 ) on sleeve ( 8 ) , using .078 allen wrench . 4 . Install spindle ( 4 ) , flat washer ( 5 ) , seal ( 6 ) ...
... flat washer ( 5 ) , seal ( 6 ) , retainer ( 3 ) , bearing ( 7 ) , and sleeve ( 8 ) . 3 . Install disks ( 9 ) and setscrews ( 10 ) on sleeve ( 8 ) , using .078 allen wrench . 4 . Install spindle ( 4 ) , flat washer ( 5 ) , seal ( 6 ) ...
4-62. lappuse
... flat tip screwdriver , remove two screws ( 1 ) and two lockwashers ( 2 ) from mount ( 3 ) . Remove housing ( 4 ) and gasket ( 5 ) from mount ( 3 ) . Using flat tip screwdriver , remove screw ( 6 ) and lock washer ( 7 ) holding terminal ...
... flat tip screwdriver , remove two screws ( 1 ) and two lockwashers ( 2 ) from mount ( 3 ) . Remove housing ( 4 ) and gasket ( 5 ) from mount ( 3 ) . Using flat tip screwdriver , remove screw ( 6 ) and lock washer ( 7 ) holding terminal ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint