Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 9.
4-12. lappuse
... clockwise to free bracket ( 9 ) from turret pad and pins ( 10 ) . 4. Rotate adjuster ( 7 ) clockwise and remove temperature compensating rod ( 4 ) . GO TO FRAME 8 Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) 7 6 4-12 Vol II TM ...
... clockwise to free bracket ( 9 ) from turret pad and pins ( 10 ) . 4. Rotate adjuster ( 7 ) clockwise and remove temperature compensating rod ( 4 ) . GO TO FRAME 8 Para 4-4 Cont 4-4 . BALLISTICS DRIVE REMOVAL ( CONT ) 7 6 4-12 Vol II TM ...
4-20. lappuse
... clockwise to lengthen rod ( 4 ) . Repairman B , using 9/16 " wrench , install two screws ( 7 ) , two lockwashers ( 8 ) , and two flat washers ( 9 ) into mounting bracket ( 5 ) and mounting pad ( 1 ) . Repairman A , using 3/4 " wrench ...
... clockwise to lengthen rod ( 4 ) . Repairman B , using 9/16 " wrench , install two screws ( 7 ) , two lockwashers ( 8 ) , and two flat washers ( 9 ) into mounting bracket ( 5 ) and mounting pad ( 1 ) . Repairman A , using 3/4 " wrench ...
4-22. lappuse
... clockwise to lengthen rod ( 4 ) . Repairman B , using 9/16 " wrench , install two screws ( 7 ) , two lockwashers ( 8 ) , and two flat washers ( 9 ) into mounting bracket ( 5 ) and mounting pad ( 1 ) . Repairman A , using 3/4 " wrench ...
... clockwise to lengthen rod ( 4 ) . Repairman B , using 9/16 " wrench , install two screws ( 7 ) , two lockwashers ( 8 ) , and two flat washers ( 9 ) into mounting bracket ( 5 ) and mounting pad ( 1 ) . Repairman A , using 3/4 " wrench ...
4-30. lappuse
... clockwise , then , turn counterclockwise to the number of turns marked on qualification plate ( 2 ) . Aline mark on output shaft ( 1 ) with index mark on qualification plate ( 2 ) . 3 . Set electronic computer to " zero " elevation . 4 ...
... clockwise , then , turn counterclockwise to the number of turns marked on qualification plate ( 2 ) . Aline mark on output shaft ( 1 ) with index mark on qualification plate ( 2 ) . 3 . Set electronic computer to " zero " elevation . 4 ...
4-41. lappuse
... removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 . TEMPERATURE COMPENSATING ROD INSTALLATION TOOLS : 3/4 " 4-41 TM 9-1220-220-34 4-41.
... removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 . TEMPERATURE COMPENSATING ROD INSTALLATION TOOLS : 3/4 " 4-41 TM 9-1220-220-34 4-41.
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint