Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 12.
4-25. lappuse
... capscrew ( JPG ) . Using torque wrench , tighten four capscrews ( 4 ) 5 foot - pounds per capscrew ( JPG ) . 4 . 5 . Do steps 2 and 3 adding 5 foot - pounds per capscrew until torque on capscrew ( 3 ) and ( 4 ) is 30 to 33 foot - pounds ...
... capscrew ( JPG ) . Using torque wrench , tighten four capscrews ( 4 ) 5 foot - pounds per capscrew ( JPG ) . 4 . 5 . Do steps 2 and 3 adding 5 foot - pounds per capscrew until torque on capscrew ( 3 ) and ( 4 ) is 30 to 33 foot - pounds ...
4-42. lappuse
... capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined surface as shown. Slide pin (7) through lugs (4 and 6). 4. Place washer (8) on pin (7). Install cotter pin (9) (JPG). FRAME 1 Step ...
... capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined surface as shown. Slide pin (7) through lugs (4 and 6). 4. Place washer (8) on pin (7). Install cotter pin (9) (JPG). FRAME 1 Step ...
4-41. lappuse
... capscrew ( 6 ) . NOTE 4 . Count and record number of turns while removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 . TEMPERATURE ...
... capscrew ( 6 ) . NOTE 4 . Count and record number of turns while removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 . TEMPERATURE ...
4-42. lappuse
... capscrew ( 3 ) . Place two lugs ( 4 ) of bracket ( 5 ) over the lug ( 6 ) of the rod ( 2 ) with machined surface as shown . Slide pin ( 7 ) through lugs ( 4 and 6 ) . Place washer ( 8 ) on pin ( 7 ) . Install cotter pin ( 9 ) ( JPG ) ...
... capscrew ( 3 ) . Place two lugs ( 4 ) of bracket ( 5 ) over the lug ( 6 ) of the rod ( 2 ) with machined surface as shown . Slide pin ( 7 ) through lugs ( 4 and 6 ) . Place washer ( 8 ) on pin ( 7 ) . Install cotter pin ( 9 ) ( JPG ) ...
4-44. lappuse
... capscrew ( 1 ) . 2 . Holding tube ( 2 ) , unscrew connector assembly ( 3 ) . 3 . Using 7/8 " box end wrench , loosen capscrew ( 4 ) . 4 . Holding tube ( 2 ) , unscrew connector assembly ( 5 ) clockwise ( left - hand thread ) . END OF ...
... capscrew ( 1 ) . 2 . Holding tube ( 2 ) , unscrew connector assembly ( 3 ) . 3 . Using 7/8 " box end wrench , loosen capscrew ( 4 ) . 4 . Holding tube ( 2 ) , unscrew connector assembly ( 5 ) clockwise ( left - hand thread ) . END OF ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint