Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.3. rezultāts no 3.
4-28. lappuse
... bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open end wrench , loosen two screws ( 8 ) and ( 9 ) . 5 . Using 1 1/4 " open end wrench ...
... bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open end wrench , loosen two screws ( 8 ) and ( 9 ) . 5 . Using 1 1/4 " open end wrench ...
4-37. lappuse
... bubble ( 1 ) is centered ( TM 9-1240-240-34 ) . If bubble is centerd , go to frame 13. If bubble is not centered , go to step 2 . 2 . Using wire cutters , cut lockwire ( 2 ) . 3 . Using 3/4 " open end wrench , loosen two screws ( 3 ) ...
... bubble ( 1 ) is centered ( TM 9-1240-240-34 ) . If bubble is centerd , go to frame 13. If bubble is not centered , go to step 2 . 2 . Using wire cutters , cut lockwire ( 2 ) . 3 . Using 3/4 " open end wrench , loosen two screws ( 3 ) ...
4-58. lappuse
... bubble in gunner's quadrant is centered ( TM 9-2350- 232-10 ) . Check ballistics drive bubble ( 2 ) is centered . NOTE 4 . 5 . If bubble is centered , go to step 4 : if not continue with step 2 . Using spanner wrench , loosen ring ( 3 ) ...
... bubble in gunner's quadrant is centered ( TM 9-2350- 232-10 ) . Check ballistics drive bubble ( 2 ) is centered . NOTE 4 . 5 . If bubble is centered , go to step 4 : if not continue with step 2 . Using spanner wrench , loosen ring ( 3 ) ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint