Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 35.
3-1. lappuse
... open end wrench 5/64 " socket head screw key ( Allen wrench or equivalent ) 3/8 " drive ratchet wrench 5/16 " hexagon stud socket ( 3/8 ′′ drive ) 6 " extension ( 3/8 ′′ drive ) 3/8 ′′ universal joint 0.075 " to 0.085 " adjustable face ...
... open end wrench 5/64 " socket head screw key ( Allen wrench or equivalent ) 3/8 " drive ratchet wrench 5/16 " hexagon stud socket ( 3/8 ′′ drive ) 6 " extension ( 3/8 ′′ drive ) 3/8 ′′ universal joint 0.075 " to 0.085 " adjustable face ...
3-4. lappuse
... open end wrench , check Tighten . Replace if missing . 1 . that two screws ( 1 ) are tight . 2 . Check that junction box input Adjust junction box . shaft ( 2 ) turns freely when universal joint ( 3 ) is disconnected from shaft assembly ...
... open end wrench , check Tighten . Replace if missing . 1 . that two screws ( 1 ) are tight . 2 . Check that junction box input Adjust junction box . shaft ( 2 ) turns freely when universal joint ( 3 ) is disconnected from shaft assembly ...
3-6. lappuse
... open end wrench , check that eight screws ( 1 ) are tight . Maintenance Action Reference Tighten or replace if missing . 2 . Check surfaces of two mounting supports ( 2 ) for nicks or burrs . Remove , nicks or burrs . 3 . Using 9/16 " open ...
... open end wrench , check that eight screws ( 1 ) are tight . Maintenance Action Reference Tighten or replace if missing . 2 . Check surfaces of two mounting supports ( 2 ) for nicks or burrs . Remove , nicks or burrs . 3 . Using 9/16 " open ...
3-8. lappuse
... open end wrench , check that three screws ( 1 ) are tight . Check that electrical wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight ...
... open end wrench , check that three screws ( 1 ) are tight . Check that electrical wires ( 2 ) and connectors ( 3 ) on interference switch ( 4 ) are not damaged . Using 9/16 " open end wrench , check that two screws ( 5 ) are tight ...
3-10. lappuse
... open end wrench , Tighten . Replace if missing . check that nut ( 3 ) is tight . 4 . Using 7/16 " open end Tighten . Replace if missing . wrench , check that screw ( 5 ) is tight . 5 . Using 1 1/16 " open end Tighten . Replace if missing .
... open end wrench , Tighten . Replace if missing . check that nut ( 3 ) is tight . 4 . Using 7/16 " open end Tighten . Replace if missing . wrench , check that screw ( 5 ) is tight . 5 . Using 1 1/16 " open end Tighten . Replace if missing .
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint