Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 8.
4-28. lappuse
... bearing cap ( 5 ) , tighten four screws ( 11 ) . Look and see if fire control ( 6 ) bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open ...
... bearing cap ( 5 ) , tighten four screws ( 11 ) . Look and see if fire control ( 6 ) bubble is centered . If not centered , go to step 3. If centered , go to frame 8 . 3 . Using wire cutters , cut lockwire ( 7 ) . 4 . Using 15/16 " open ...
4-29. lappuse
... . 3 BALLISTICS DRIVE INSTALLATION ( CONT ) 2 1 4 ( 11 ) VIEW FROM OTHER SIDE WRENCH 9 6 SLOT 10 8 7 5 QUALIFICATION MARK ON EACH BEARING CAP Para 4-5 Cont 4-5 . FRAME 8 Step BALLISTICS DRIVE INSTALLATION ( CONT. Vol II 4-29 TM 9-1220-220- ...
... . 3 BALLISTICS DRIVE INSTALLATION ( CONT ) 2 1 4 ( 11 ) VIEW FROM OTHER SIDE WRENCH 9 6 SLOT 10 8 7 5 QUALIFICATION MARK ON EACH BEARING CAP Para 4-5 Cont 4-5 . FRAME 8 Step BALLISTICS DRIVE INSTALLATION ( CONT. Vol II 4-29 TM 9-1220-220- ...
4-46. lappuse
... bearings ( 10 ) , seals ( 11 and 12 ) , and stud ( 13 ) . Discard seals if damaged . 6 . Remove disks ( 14 ) by tightening setscrews ( 3 ) , using .050 allen wrench . 7 . Discard disks ( 14 ) and remove setscrews ( 3 ) . Para 4-12 END ...
... bearings ( 10 ) , seals ( 11 and 12 ) , and stud ( 13 ) . Discard seals if damaged . 6 . Remove disks ( 14 ) by tightening setscrews ( 3 ) , using .050 allen wrench . 7 . Discard disks ( 14 ) and remove setscrews ( 3 ) . Para 4-12 END ...
4-48. lappuse
... bearings ( 4 ) , and seal ( 5 ) . 2 . Install flat washer ( 6 ) , lockwasher ( 7 ) , and cap screw ( 8 ) . 3 . Install pillow block cap ( 9 ) on connector ( 10 ) , using 2 3/16 pin spanner wrench . 4 . Install disks ( 11 ) and setscrews ...
... bearings ( 4 ) , and seal ( 5 ) . 2 . Install flat washer ( 6 ) , lockwasher ( 7 ) , and cap screw ( 8 ) . 3 . Install pillow block cap ( 9 ) on connector ( 10 ) , using 2 3/16 pin spanner wrench . 4 . Install disks ( 11 ) and setscrews ...
4-50. lappuse
... bearing ( 9 ) , retainer ( 10 ) , seal ( 11 ) , flat washer ( 12 ) and spindle ( 13 ) . Tighten setscrews ( 14 ) to remove disks ( 15 ) , using .078 allen wrench . Discard disks ( 15 ) and remove setscrews ( 14 ) . Tighten setscrews ...
... bearing ( 9 ) , retainer ( 10 ) , seal ( 11 ) , flat washer ( 12 ) and spindle ( 13 ) . Tighten setscrews ( 14 ) to remove disks ( 15 ) , using .078 allen wrench . Discard disks ( 15 ) and remove setscrews ( 14 ) . Tighten setscrews ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint