Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 7.
4-12. lappuse
... adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) . Using pry bar , pry bracket ( 9 ) from turret pad while rotating adjuster ( 7 ) using 1-1 / 16 " open wrench counter clockwise to ...
... adjuster ( 7 ) . CAUTION 3 . Exercise care when removing bracket ( 9 ) to prevent damage to pins ( 10 ) . Using pry bar , pry bracket ( 9 ) from turret pad while rotating adjuster ( 7 ) using 1-1 / 16 " open wrench counter clockwise to ...
4-20. lappuse
... adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) ...
... adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) ...
4-22. lappuse
... adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) ...
... adjuster ( 2 ) into support arm ( 3 ) . Turn adjuster ( 2 ) by hand to mesh threads . Repairman A , using 1-1 / 16 " wrench , screw adjuster ( 2 ) into support arm ( 3 ) and rod ( 4 ) until clearance is enough to mount bracket ( 5 ) ...
4-28. lappuse
... adjuster arm ( 10 ) until fire control level ( 6 ) bubble is centered . 6 . Using 15/16 open end wrench , tighten two screws ( 8 ) and ( 9 ) . 7 . Using lockwire tool , install new lockwire ( 7 ) ( JPG ) . GO TO FRAME 8 Para 4-5 Cont 34 ...
... adjuster arm ( 10 ) until fire control level ( 6 ) bubble is centered . 6 . Using 15/16 open end wrench , tighten two screws ( 8 ) and ( 9 ) . 7 . Using lockwire tool , install new lockwire ( 7 ) ( JPG ) . GO TO FRAME 8 Para 4-5 Cont 34 ...
4-42. lappuse
... adjuster (1) on rod (2) counterclockwise (left-hand thread) the number of turns recorded during removal procedure. 2. Using wrench, tighten capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined ...
... adjuster (1) on rod (2) counterclockwise (left-hand thread) the number of turns recorded during removal procedure. 2. Using wrench, tighten capscrew (3). 3. Place two lugs (4) of bracket (5) over the lug (6) of the rod (2) with machined ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint