Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 69.
13. lappuse
... FORM 2404 DO FINAL INSPECTION ( VOL II , CHAP 5 ) H END OF JOB YES ALL FAULT SYMPTOMS CORRECTED NO DS / GS SENDS BAD ASSEMBLY TO DEPOT FOR REPAIR END OF JOB Para 1-3 Cont 1-3 2-2 . FRAME 2 Step Procedure 1 . 2 . Vol I.
... FORM 2404 DO FINAL INSPECTION ( VOL II , CHAP 5 ) H END OF JOB YES ALL FAULT SYMPTOMS CORRECTED NO DS / GS SENDS BAD ASSEMBLY TO DEPOT FOR REPAIR END OF JOB Para 1-3 Cont 1-3 2-2 . FRAME 2 Step Procedure 1 . 2 . Vol I.
2-2. lappuse
... Step Procedure 1 . Set COMPUTER SWITCH ( 1 ) on range finder ( 2 ) to OFF . 2 . Pull out and turn range correction knob ( 3 ) on ballistics computer ( 4 ) until scale ( 5 ) reads 0 ( zero ) . 3. While looking into range scale window ( 6 ) ...
... Step Procedure 1 . Set COMPUTER SWITCH ( 1 ) on range finder ( 2 ) to OFF . 2 . Pull out and turn range correction knob ( 3 ) on ballistics computer ( 4 ) until scale ( 5 ) reads 0 ( zero ) . 3. While looking into range scale window ( 6 ) ...
2-4. lappuse
... Step Procedure 1 . 2 . 3 . 4 . 5 . Set range correction knob ( 1 ) on ballistics computer ( 2 ) according to the number of effective rounds fired ( see log book and decal on cover ( 3 ) ) . Pull range correction knob ( 1 ) out and turn ...
... Step Procedure 1 . 2 . 3 . 4 . 5 . Set range correction knob ( 1 ) on ballistics computer ( 2 ) according to the number of effective rounds fired ( see log book and decal on cover ( 3 ) ) . Pull range correction knob ( 1 ) out and turn ...
2-6. lappuse
... Step Procedure 1 . Check that ballistic computer ( 1 ) does not move back and forth more than ten times or does not ... step 1 only ; then go to para 4-5 , frame 2 ) . Para 2-2 Cont 2-2 . FRAME 4 Step Procedure 1 . 2 . 2-6 Vol I TM 9 ...
... Step Procedure 1 . Check that ballistic computer ( 1 ) does not move back and forth more than ten times or does not ... step 1 only ; then go to para 4-5 , frame 2 ) . Para 2-2 Cont 2-2 . FRAME 4 Step Procedure 1 . 2 . 2-6 Vol I TM 9 ...
2-8. lappuse
... Step Procedure 1 . 2 . Set circuit breaker switch ( 1 ) to OFF . While looking into range view housing window ( 2 ) ... procedure ( TM 9-254 ) . b . Repair range finder link connector assembly ( Vol II , para 4-20 ) . 2-2 . FRAME 5 Step ...
... Step Procedure 1 . 2 . Set circuit breaker switch ( 1 ) to OFF . While looking into range view housing window ( 2 ) ... procedure ( TM 9-254 ) . b . Repair range finder link connector assembly ( Vol II , para 4-20 ) . 2-2 . FRAME 5 Step ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint