Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 100.
13. lappuse
... TASKS F G LISTED ON DA FORM 2404 DO FINAL INSPECTION ( VOL II , CHAP 5 ) H END OF JOB YES ALL FAULT SYMPTOMS CORRECTED NO DS / GS SENDS BAD ASSEMBLY TO DEPOT FOR REPAIR END OF JOB Para 1-3 Cont 1-3 2-2 . FRAME 2 Step Procedure 1 . 2 . Vol ...
... TASKS F G LISTED ON DA FORM 2404 DO FINAL INSPECTION ( VOL II , CHAP 5 ) H END OF JOB YES ALL FAULT SYMPTOMS CORRECTED NO DS / GS SENDS BAD ASSEMBLY TO DEPOT FOR REPAIR END OF JOB Para 1-3 Cont 1-3 2-2 . FRAME 2 Step Procedure 1 . 2 . Vol ...
14. lappuse
... 00-933-1203). TM 9-1220-220-34 1-4 . TEST EQUIPMENT No special test equipment is needed to do the performance test on the M10 Series Ballistics Drive . Para 1-4 CHAPTER 2 TROUBLESHOOTING 2-1 . SCOPE Troubleshooting of the M10 1-4 Vol I.
... 00-933-1203). TM 9-1220-220-34 1-4 . TEST EQUIPMENT No special test equipment is needed to do the performance test on the M10 Series Ballistics Drive . Para 1-4 CHAPTER 2 TROUBLESHOOTING 2-1 . SCOPE Troubleshooting of the M10 1-4 Vol I.
2-4. lappuse
... para 4-4 , frame 4 , and para 4-5 , frame 9 ) . GO TO FRAME 3 Para 2-2 Cont Vol I 2-2 . FRAME 3 Step Procedure 1 . Check that 2-4 TM 9-1220-220-34.
... para 4-4 , frame 4 , and para 4-5 , frame 9 ) . GO TO FRAME 3 Para 2-2 Cont Vol I 2-2 . FRAME 3 Step Procedure 1 . Check that 2-4 TM 9-1220-220-34.
2-6. lappuse
... para 4-5 , frame 2 ) . Para 2-2 Cont 2-2 . FRAME 4 Step Procedure 1 . 2 . 2-6 Vol I TM 9-1220-220-34.
... para 4-5 , frame 2 ) . Para 2-2 Cont 2-2 . FRAME 4 Step Procedure 1 . 2 . 2-6 Vol I TM 9-1220-220-34.
2-8. lappuse
... Para 2-1 GO TO FRAME 5 Do maintenance procedure ( TM 9-254 ) . b . Repair range finder link connector assembly ( Vol II , para 4-20 ) . 2-2 . FRAME 5 Step Procedure 1 . Set circuit 2-8 Vol I TM 9-1220-220-34.
... Para 2-1 GO TO FRAME 5 Do maintenance procedure ( TM 9-254 ) . b . Repair range finder link connector assembly ( Vol II , para 4-20 ) . 2-2 . FRAME 5 Step Procedure 1 . Set circuit 2-8 Vol I TM 9-1220-220-34.
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint