Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 29.
2-1. lappuse
... Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
... Ballistics drive mounted on vehicle PRELIMINARY PROCEDURES : Remove firing mechanism of gun tube ( TM 10 ) Para 2-1 2-2 . PERFORMANCE TEST ( CONT ) NOTE Performance test Vol I 2-1 TM 9-1220-220-34 HOW TO USE THIS MANUAL CHAPTER.
2-2. lappuse
... NOTE Performance test should be performed operating the system manually . FRAME 1 Step Procedure 1 . Set COMPUTER SWITCH ( 1 ) on range finder ( 2 ) to OFF . 2 . Pull out and turn range correction knob ( 3 ) on ballistics computer ( 4 ) ...
... NOTE Performance test should be performed operating the system manually . FRAME 1 Step Procedure 1 . Set COMPUTER SWITCH ( 1 ) on range finder ( 2 ) to OFF . 2 . Pull out and turn range correction knob ( 3 ) on ballistics computer ( 4 ) ...
2-4. lappuse
... Note the reading of outer 7 . Symptom Maintenance Action : pointer ( 8 ) of ballistics computer ( 2 ) . Check that range movement ( reading of outer pointer ( 8 ) ) is the same as reading on inner pointer ( 9 ) . Range movement is not ...
... Note the reading of outer 7 . Symptom Maintenance Action : pointer ( 8 ) of ballistics computer ( 2 ) . Check that range movement ( reading of outer pointer ( 8 ) ) is the same as reading on inner pointer ( 9 ) . Range movement is not ...
2-16. lappuse
... NOTE Do steps 1 thru 3 for M10 , M10A1 , and M10A6 config- urations only . 1 . Remove electrical connector ( 1 ) from housing ( 2 ) . 2 . Using multimeter , check that Faulty light assembly . resistance between housing ( 2 ) and plug ...
... NOTE Do steps 1 thru 3 for M10 , M10A1 , and M10A6 config- urations only . 1 . Remove electrical connector ( 1 ) from housing ( 2 ) . 2 . Using multimeter , check that Faulty light assembly . resistance between housing ( 2 ) and plug ...
3-1. lappuse
... NOTE Once the ballistics drive is removed from vehicle DS / GS does not have the tools to accurately set the fire control level if the level is tampered with . If the fire control level needs to be repaired , repair before removing ...
... NOTE Once the ballistics drive is removed from vehicle DS / GS does not have the tools to accurately set the fire control level if the level is tampered with . If the fire control level needs to be repaired , repair before removing ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint