Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 7.
2-1. lappuse
... look in the maintenance action column to find out what to do to correct it . it . 2-2 . PERFORMANCE TEST TOOLS : Multimeter SUPPLIES : Black thread Tape or strap Pencil Paper Binoculars PERSONNEL : Two REFERENCES : TM 10 Series manuals ...
... look in the maintenance action column to find out what to do to correct it . it . 2-2 . PERFORMANCE TEST TOOLS : Multimeter SUPPLIES : Black thread Tape or strap Pencil Paper Binoculars PERSONNEL : Two REFERENCES : TM 10 Series manuals ...
2-10. lappuse
... look through firing pin hole ( 6 ) in breech block ( 7 ) . ( TM 10 ) 6 . Symptom Maintenance Action : Look through eyepiece ( 8 ) of gunner's periscope ( 9 ) . Check that gunner's periscope ( 9 ) is boresighted ( aimed at same target as ...
... look through firing pin hole ( 6 ) in breech block ( 7 ) . ( TM 10 ) 6 . Symptom Maintenance Action : Look through eyepiece ( 8 ) of gunner's periscope ( 9 ) . Check that gunner's periscope ( 9 ) is boresighted ( aimed at same target as ...
2-12. lappuse
... look through firing pin hole ( 6 ) in breech block ( 7 ) . ( TM 10 ) Look through eyepiece ( 8 ) of gunner's periscope ( 9 ) . Check that gunner's peri- scope ( 9 ) is boresighted ( aimed at same target as rangefinder ( 1 ) ...
... look through firing pin hole ( 6 ) in breech block ( 7 ) . ( TM 10 ) Look through eyepiece ( 8 ) of gunner's periscope ( 9 ) . Check that gunner's peri- scope ( 9 ) is boresighted ( aimed at same target as rangefinder ( 1 ) ...
2-20. lappuse
... look for when the ballistics drive is returned to DS / GS . A complete inspection should be made and faults listed on DA Form 2404 before any repairs are made . c . Chapter 4 , Maintenance Procedures , gives step - by - step procedures ...
... look for when the ballistics drive is returned to DS / GS . A complete inspection should be made and faults listed on DA Form 2404 before any repairs are made . c . Chapter 4 , Maintenance Procedures , gives step - by - step procedures ...
4-18. lappuse
... Look to see if right support locator pin hole ( 1 ) matches up with the pin hole in turret mounting pad . If holes do not match up , do steps 2 and 3. If holes do match up , go to step 4 . If existing hole is in front of the support ...
... Look to see if right support locator pin hole ( 1 ) matches up with the pin hole in turret mounting pad . If holes do not match up , do steps 2 and 3. If holes do match up , go to step 4 . If existing hole is in front of the support ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint