Direct Support and General Support Maintenance Manual: Ballistic Drive, M10 (1220-00-676-2184), M10A1 (1220-00-076-9765), M10A3 (1220-00-572-8735), M10A4 (1220-00-856-9453), M10A5 (1220-00-980-9297), M10A6 (1220-00-933-1203).Headquarters, Department of the Army, 1985 |
No grāmatas satura
1.–5. rezultāts no 26.
2-16. lappuse
... final inspection ( Vol II , para 5-2 ) . END OF TASK Para 2-2 Cont a . Replace lamp ( TM 20-2 ) b . Disassemble light as- sembly and check for worn , corroded , or broken parts and re- place ( Vol II , para 4-15 ) . 3-2 . FRAME 1 Step 1 ...
... final inspection ( Vol II , para 5-2 ) . END OF TASK Para 2-2 Cont a . Replace lamp ( TM 20-2 ) b . Disassemble light as- sembly and check for worn , corroded , or broken parts and re- place ( Vol II , para 4-15 ) . 3-2 . FRAME 1 Step 1 ...
3-12. lappuse
... END OF TASK Para 3-2 Cont Replace missing or damaged parts . Replace missing wire seals , if installed in vehicle . Send ballistics drive to depot for repair . Para 4-6 Para 4-5 , frame 3 , steps 3 and 7 and frame 7 , steps 3 and 7 and ...
... END OF TASK Para 3-2 Cont Replace missing or damaged parts . Replace missing wire seals , if installed in vehicle . Send ballistics drive to depot for repair . Para 4-6 Para 4-5 , frame 3 , steps 3 and 7 and frame 7 , steps 3 and 7 and ...
4-42. lappuse
... end wrench 6" slip joint pliers PERSONNEL: One REFERENCES: JPG 4 1 C for installing cotter pins EQUIPMENT CONDITION ... END OF TASK Para 4-8 Vol II Section 4. TRUNNION LINK 4-9. TRUNNION LINK MAINTENANCE PROCEDURES INDEX. 4-42 TM 9-1220 ...
... end wrench 6" slip joint pliers PERSONNEL: One REFERENCES: JPG 4 1 C for installing cotter pins EQUIPMENT CONDITION ... END OF TASK Para 4-8 Vol II Section 4. TRUNNION LINK 4-9. TRUNNION LINK MAINTENANCE PROCEDURES INDEX. 4-42 TM 9-1220 ...
4-38. lappuse
... stop attached ) , using one screw ( 2 ) and one lockwasher ( 3 ) . Using screwdriver , install bracket ( 4 ) , switch ( 5 ) ... END OF TASK Para 4-5 Cont 4-5 . BALLISTICS DRIVE INSTALLATION ( CONT ) 9 7 4-38 Vol II TM 9-1220-220-34.
... stop attached ) , using one screw ( 2 ) and one lockwasher ( 3 ) . Using screwdriver , install bracket ( 4 ) , switch ( 5 ) ... END OF TASK Para 4-5 Cont 4-5 . BALLISTICS DRIVE INSTALLATION ( CONT ) 9 7 4-38 Vol II TM 9-1220-220-34.
4-41. lappuse
... end wrench , loosen capscrew ( 6 ) . NOTE 4 . Count and record number of turns while removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 ...
... end wrench , loosen capscrew ( 6 ) . NOTE 4 . Count and record number of turns while removing adjuster ( 7 ) . Holding rod ( 5 ) , unscrew adjuster ( 7 ) clockwise ( left - hand thread ) . END OF TASK 6 7 3 5 1 2 Vol II Para 4-7 4-8 ...
Bieži izmantoti vārdi un frāzes
050 allen wrench 3/16 pin spanner BALLISTICS DRIVE INSPECTION BALLISTICS DRIVE INSTALLATION BALLISTICS DRIVE REMOVAL box end wrench capscrew circuit breaker switch cotter pin DRIVE CONNECTOR DRIVE INSTALLATION CONT DRIVE REMOVAL CONT elevation quadrant END OF TASK EQUIPMENT CONDITION fire control level flat tip screwdriver flat washer foot-pounds four lockwashers FRAME 1 Step GO TO FRAME gunner's periscope holding cap hose clamp INSPECTION UPON RECEIPT JPG 41C junction box assembly LEVEL VIAL LIGHT ASSEMBLY link connector assembly lockwire M10 Series Ballistics NOTE FOLLOW-ON MAINTENANCE number of turns open end wrench Para 4-5 Cont Para Para PERFORMANCE TEST CONT performance test Vol pin spanner wrench range finder rangefinder link connector RECEIPT CONT remove four screws Repairman Replace if missing Series Ballistics Drive Set circuit breaker SHAFT AND RELATED SIDE OF CONNECTING Step BALLISTICS DRIVE Step Procedure SUPERELEVATION BOX ASSEMBLY temperature compensating rod torque wrench trunnion link turret mounting pad universal joint