5.

"SELF-KILL" results when orange weapon key is put in the control console receptacle (5) and turned to WEAPON position. A code of 99 will show on the LCA display, the CVKI light will flash continuously, and the NOT READY light will light. When the orange weapon key is removed, a continuous tone will be heard in the intercom. You must then call the controller to reset your system.

If your tank is "KILLED," the main gun and coax machine gun transmitters are automatically turned off.

To silence your intercom alarm after a "KILL" remove the orange weapon key from the M2 machine gun transmitter (1) and insert in the control console. The transmitter will no longer fire. Remove yellow key from M240 machine gun transmitter and insert into your torso harness.

Insert the orange key (2) in the control console receptacle and turn off the intercom alarm. IF YOU REMOVE KEY FROM RECEPTACLE, THE ALARM WILL BEGIN AGAIN. The CVKI light continues to flash. It can be turned off only by the controller.

To reset: Remove orange weapon key. Alarm will sound. Ask the controller to turn off your intercom alarm and CVKI light. This resets control console.

Turn control console switch (3) to MAIN GUN. Press the display button (4). Display (5) should show 55. If no 55, turn to Troubleshooting, page 3-4.

Put your orange key back in the M2 transmitter and turn it to WEAPON ON.

Put your yellow key back in the M240 transmitter and turn it to WEAPON ON.

The controller will determine when to reset your system.

Postoperational and Storage Tasks - Index Remove, inspect, service and return all
MILES equipment following completion of training exercise.

If you need additional information on completing a post-
operational task, turn to referenced section. Postoperational
task will be reverse of referenced section.

Postoperational and Storage Task 1: Return Fire Control Computer to Automatic
Status. (Except where indicated, task applies only to M1 tank, not M1A1 tank).

Enter into computer original BORESIGHT numbers recorded during step 9, Align subtask 1-A (M1 tank), or step 13, Align Subtask 1.1-A (M1A1 tank).

Enter original ZERO numbers recorded during step 12, Align subtask 1-A, into computer.

Enter original AMMO SUBDES numbers recorded during step 35, Align subtask 1-B, into computer.

Verify that LEAD, CANT, CROSSWIND and RANGE keys are NOT lit. This indicates that Fire
Control computer has been returned to automatic mode.

Realign GUNNER AUXILIARY SIGHT (GAS) and M105D sight.

NOTE

For assistance in returning computer to auxiliary mode
consult TM 9-2350-255-10, Operator's Manual: M1 Tank.

C

Postoperational and Storage Task 2: MWLD Postoperational Tasks

Remove MWLD Harnesses. See MWLD Tasks 5 and 6.

Remove batteries from MWLD harnesses and close battery doors. See MWLD Task 4.

Inspect and service the MWLD. See MWLD Tasks 2 and 3.

Postoperational and Storage Task 3: M240 MG Postoperational Tasks.

Remove M240 transmitter. See M240 MG Task 4.

Remove the battery from the M240 transmitter and close battery compartment door. See M240 MG Task 3.

Inspect and service M240 MG transmitter. See M240 MG Task 2.

Remove, inspect, and service M240 MG blank firing attachment. See TM 9-1005-313-10

Postoperational and Storage Task 4: M2 MG Postoperational Tasks.

Remove M2 transmitter. See M2 MG Task 4.

Remove the battery from M2 transmitter and close battery compartment door. See M2 MG Task 3.

Inspect and service M2 MG transmitter. See M2 MG Task 2.

Remove, inspect, and service M2 MG blank firing attachment. See TM 9-1005-314-12&P.