Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 31.
2-36. lappuse
... open - end wrenches , remove bolt ( 9 ) and nut ( 10 ) from rocket harness connector ( 11 ) . NOTE Ensure that bridle cable is not twisted . 7 ai . Slip rocket bridle cable loop ( 12 ) 2-36 TM 9-1375-215-14 & P.
... open - end wrenches , remove bolt ( 9 ) and nut ( 10 ) from rocket harness connector ( 11 ) . NOTE Ensure that bridle cable is not twisted . 7 ai . Slip rocket bridle cable loop ( 12 ) 2-36 TM 9-1375-215-14 & P.
2-37. lappuse
... open - end wrenches , tighten nut ( 10 ) onto bolt ( 9 ) . • CAUTIONS Ensure rocket harness connector ( 11 ) is pointed forward and positioned near front of linear demoli- tion charge container . Ensure that shock cords at rear of cover ...
... open - end wrenches , tighten nut ( 10 ) onto bolt ( 9 ) . • CAUTIONS Ensure rocket harness connector ( 11 ) is pointed forward and positioned near front of linear demoli- tion charge container . Ensure that shock cords at rear of cover ...
4-19. lappuse
... combination box- and open - end wrench . 4. Using a 7 / 16 - inch socket wrench , remove the hex - head capscrew ( 3 ) and flatwasher ( 4 ) . Remove and retain the spring ( 5 ) . 5. Remove retaining ring ( 7 ) from groove in crosspiece ...
... combination box- and open - end wrench . 4. Using a 7 / 16 - inch socket wrench , remove the hex - head capscrew ( 3 ) and flatwasher ( 4 ) . Remove and retain the spring ( 5 ) . 5. Remove retaining ring ( 7 ) from groove in crosspiece ...
4-20. lappuse
... combination box- and open - end wrench so that head of bolt is pointed toward the center . 2. Thread hex nut ( 10 ) and hand knob ( 11 ) onto hex bolt ( 12 ) . 3. Slide crosspiece ( 8 ) into launcher rail so that hand knobs will be ...
... combination box- and open - end wrench so that head of bolt is pointed toward the center . 2. Thread hex nut ( 10 ) and hand knob ( 11 ) onto hex bolt ( 12 ) . 3. Slide crosspiece ( 8 ) into launcher rail so that hand knobs will be ...
4-21. lappuse
... socket wrench and a 1 / 2 - inch combination box- and open - end wrench . 4-13 . REPLACE ROCKET RELEASE MECHANISM . This task covers : Remove and Replace INITIAL SETUP Tools General mechanic's tool kit ( item 12 , section III , appendix ...
... socket wrench and a 1 / 2 - inch combination box- and open - end wrench . 4-13 . REPLACE ROCKET RELEASE MECHANISM . This task covers : Remove and Replace INITIAL SETUP Tools General mechanic's tool kit ( item 12 , section III , appendix ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew