Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 51.
2-10. lappuse
... nections . LAUNCHER . Wipe with rags ( wash if necessary ) . Part missing or dam- aged . Part missing , dam- aged , or cable con- nections are loose . Table 2-1 . Operator PMCS ( Cont ) D During 2-10 TM 9-1375-215-14 & P.
... nections . LAUNCHER . Wipe with rags ( wash if necessary ) . Part missing or dam- aged . Part missing , dam- aged , or cable con- nections are loose . Table 2-1 . Operator PMCS ( Cont ) D During 2-10 TM 9-1375-215-14 & P.
2-15. lappuse
... necessary to raise or lower the launcher rail slightly . This is achieved by using the hand pump or release valve handle while hydraulic con- trol valve is in manual position . Mos 2-9 . PRESSURE CHECKOUT . 3 JOUN O • •. Mine Clearing ...
... necessary to raise or lower the launcher rail slightly . This is achieved by using the hand pump or release valve handle while hydraulic con- trol valve is in manual position . Mos 2-9 . PRESSURE CHECKOUT . 3 JOUN O • •. Mine Clearing ...
2-17. lappuse
... necessary to raise or lower the launcher rail slightly . This is achieved by using the hand pump or release valve handle while hydraulic con- trol valve handle is in manual position . a . Engage detents ( 1 ) by pulling down on levers ...
... necessary to raise or lower the launcher rail slightly . This is achieved by using the hand pump or release valve handle while hydraulic con- trol valve handle is in manual position . a . Engage detents ( 1 ) by pulling down on levers ...
2-20. lappuse
... necessary to raise or lower the launcher rail slightly . The 15 / 16 - inch socket wrench from RPSTL is re- quired for this operation . a . Ensure that release valve handle ( 1 ) is forward in HOLD position and hydraulic control valve ...
... necessary to raise or lower the launcher rail slightly . The 15 / 16 - inch socket wrench from RPSTL is re- quired for this operation . a . Ensure that release valve handle ( 1 ) is forward in HOLD position and hydraulic control valve ...
2-22. lappuse
... necessary , move trailer to designated area for loading linear demolition charge container . 2-11 . LOADING LINEAR DEMOLITION CHARGE CONTAINER ON LAUNCHER . 3 1 4 2 a . b . NOTE When removing or inserting ball 2-22 TM 9-1375-215-14 & P 2- ...
... necessary , move trailer to designated area for loading linear demolition charge container . 2-11 . LOADING LINEAR DEMOLITION CHARGE CONTAINER ON LAUNCHER . 3 1 4 2 a . b . NOTE When removing or inserting ball 2-22 TM 9-1375-215-14 & P 2- ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew