Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 28.
1-6. lappuse
... hose . When the hydraulic control valve is positioned to apply hydraulic pressure to the actuating cylinder , the cylinder ex- tends to raise the launch rail . When hydraulic pressure to the actuating cylinder is released , the weight ...
... hose . When the hydraulic control valve is positioned to apply hydraulic pressure to the actuating cylinder , the cylinder ex- tends to raise the launch rail . When hydraulic pressure to the actuating cylinder is released , the weight ...
2-3. lappuse
... hose . PRESSURE GAGE . Indicates accumulator hydraulic pressure . HAND PUMP RELEASE VALVE . When closed , or in the HOLD position , allows hand pump to deliver hydraulic fluid . When open , or in the RELEASE position , causes fluid to ...
... hose . PRESSURE GAGE . Indicates accumulator hydraulic pressure . HAND PUMP RELEASE VALVE . When closed , or in the HOLD position , allows hand pump to deliver hydraulic fluid . When open , or in the RELEASE position , causes fluid to ...
2-13. lappuse
... hose ( 16 ) , cracked lines ( 17 ) , and loose fittings ( 18 ) . 16 Equipment Is Not Ready / Available If : Assembly leaks , fit- tings loose , or part damaged . 17 18 Hand pump leaks . CAUTION Pump reservoir holds only 2-1 / 2 qt ( 2.4 ...
... hose ( 16 ) , cracked lines ( 17 ) , and loose fittings ( 18 ) . 16 Equipment Is Not Ready / Available If : Assembly leaks , fit- tings loose , or part damaged . 17 18 Hand pump leaks . CAUTION Pump reservoir holds only 2-1 / 2 qt ( 2.4 ...
31. lappuse
... Hose down or wipe down launcher if extremely dirty . NOTE Avoid steam cleaning hydraulic components unless ab- solutely necessary . Lubricate all parts , joints , and hinges after components have been washed or steam cleaned . Use rags ...
... Hose down or wipe down launcher if extremely dirty . NOTE Avoid steam cleaning hydraulic components unless ab- solutely necessary . Lubricate all parts , joints , and hinges after components have been washed or steam cleaned . Use rags ...
4-1. lappuse
... Hydraulic Check Valve . 4-39 Replace Fluid Dampener 4-40 Repair Hydraulic Hose , Lines , and Fittings 4-41 Replace Lanyard . . . 4-45 Touch - Up Painting 4-47 Section I. REPAIR PARTS , SPECIAL TOOLS ; TEST , 4-1 TM 9-1375-215-14 & P.
... Hydraulic Check Valve . 4-39 Replace Fluid Dampener 4-40 Repair Hydraulic Hose , Lines , and Fittings 4-41 Replace Lanyard . . . 4-45 Touch - Up Painting 4-47 Section I. REPAIR PARTS , SPECIAL TOOLS ; TEST , 4-1 TM 9-1375-215-14 & P.
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew