Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 30.
1-13. lappuse
... forward enough to reduce tension on arresting cable . Wait 30 minutes in case of hangfire . ( 4 ) Check all electrical connections to linear charge for proper assembly . Correct problems immediately . Repeat firing sequence . ( 5 ) If ...
... forward enough to reduce tension on arresting cable . Wait 30 minutes in case of hangfire . ( 4 ) Check all electrical connections to linear charge for proper assembly . Correct problems immediately . Repeat firing sequence . ( 5 ) If ...
2-12. lappuse
... forward when handle ( 13 ) is pulled . b . Ensure cotter pin ( 14 ) is not missing or damaged . Ensure that cam ( 12 ) is for- ward and under pin weldment ( 15 ) of right launcher rail support . c . Lubricate moving parts with light oil ...
... forward when handle ( 13 ) is pulled . b . Ensure cotter pin ( 14 ) is not missing or damaged . Ensure that cam ( 12 ) is for- ward and under pin weldment ( 15 ) of right launcher rail support . c . Lubricate moving parts with light oil ...
2-17. lappuse
... forward HOLD position . Insert ball - lock pins ( 4 ) into RAISE ( side ) position in launcher rail supports ( 5 ) . Move hydraulic control valve handle ( 3 ) to PRESSURIZE ACCUMULATOR position . Pump handle ( 6 ) until resistance to ...
... forward HOLD position . Insert ball - lock pins ( 4 ) into RAISE ( side ) position in launcher rail supports ( 5 ) . Move hydraulic control valve handle ( 3 ) to PRESSURIZE ACCUMULATOR position . Pump handle ( 6 ) until resistance to ...
2-18. lappuse
... forward to HOLD position . m . Move hydraulic control valve handle ( 3 ) to PRESSURIZE ACCUMULATOR position . n . Engage detents ( 1 ) by pulling down on levers . o . Pump handle ( 6 ) until 3200 psi ( green area ) is indicated on ...
... forward to HOLD position . m . Move hydraulic control valve handle ( 3 ) to PRESSURIZE ACCUMULATOR position . n . Engage detents ( 1 ) by pulling down on levers . o . Pump handle ( 6 ) until 3200 psi ( green area ) is indicated on ...
2-20. lappuse
... forward in HOLD position and hydraulic control valve handle is in the MANUAL RAISE / LOWER position . b . Ensure ball - lock pins are removed from launcher rail supports and detent levers are in up position . CAUTION Never raise ...
... forward in HOLD position and hydraulic control valve handle is in the MANUAL RAISE / LOWER position . b . Ensure ball - lock pins are removed from launcher rail supports and detent levers are in up position . CAUTION Never raise ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew