Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.5. rezultāts no 24.
4-19. lappuse
... combination box- and open - end wrench . 3. Unscrew hand knob ( 2 ) and hex nut ( 1 ) from hex bolt ( 9 ) . Unscrew hex bolt ( 9 ) from crosspiece ( 8 ) using a 9 / 16 - inch combination box- and open - end wrench . 4. Using a 7 / 16 ...
... combination box- and open - end wrench . 3. Unscrew hand knob ( 2 ) and hex nut ( 1 ) from hex bolt ( 9 ) . Unscrew hex bolt ( 9 ) from crosspiece ( 8 ) using a 9 / 16 - inch combination box- and open - end wrench . 4. Using a 7 / 16 ...
4-20. lappuse
... combination box- and open - end wrench so that head of bolt is pointed toward the center . 2. Thread hex nut ( 10 ) ... combination box- and open - end wrench . 8. Thread hex nut ( 1 ) and hand knob ( 2 ) onto hex bolt ( 9 ) using 9 / 16 ...
... combination box- and open - end wrench so that head of bolt is pointed toward the center . 2. Thread hex nut ( 10 ) ... combination box- and open - end wrench . 8. Thread hex nut ( 1 ) and hand knob ( 2 ) onto hex bolt ( 9 ) using 9 / 16 ...
4-21. lappuse
... combination box- and open - end wrench , remove two hex nuts ( 3 ) , lockwashers ( 2 ) , and capscrews ( 1 ) which join detent assembly ( 4 ) to launcher rail support ( 5 ) . 2. Remove detent assembly ( 4 ) . 3. Inspect detent assembly ...
... combination box- and open - end wrench , remove two hex nuts ( 3 ) , lockwashers ( 2 ) , and capscrews ( 1 ) which join detent assembly ( 4 ) to launcher rail support ( 5 ) . 2. Remove detent assembly ( 4 ) . 3. Inspect detent assembly ...
4-22. lappuse
... LOCK position vid 16 8 5 3 4 7 17 11 16 15 us ) of b 11 OAL 2 1 10 bas neg 6 18 ( 13 ) ( 14 ) 12 9 REMOVE 1. Remove cam weldment cover by removing the six hex - head capscrews and lockwashers with 7 / 16 - inch combination box- and open ...
... LOCK position vid 16 8 5 3 4 7 17 11 16 15 us ) of b 11 OAL 2 1 10 bas neg 6 18 ( 13 ) ( 14 ) 12 9 REMOVE 1. Remove cam weldment cover by removing the six hex - head capscrews and lockwashers with 7 / 16 - inch combination box- and open ...
4-24. lappuse
... combination box- and open - end wrench . 4-14 . PREPARE HYDRAULIC SYSTEM FOR COMPONENT REPLACEMENT . This task covers : Remove and Install INITIAL SETUP Tools General mechanic's tool kit ( item 12 , section III , appendix B ) Industrial ...
... combination box- and open - end wrench . 4-14 . PREPARE HYDRAULIC SYSTEM FOR COMPONENT REPLACEMENT . This task covers : Remove and Install INITIAL SETUP Tools General mechanic's tool kit ( item 12 , section III , appendix B ) Industrial ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew