Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 34.
2-14. lappuse
... Clean and spot paint in accordance with maintenance procedures in section 3 or 4 . HYDRAULIC SYSTEM . Perform pressure checkout in accordance with paragraph 2-9 . Dirt or rust inhibits operation of launcher . Launch rail does not raise ...
... Clean and spot paint in accordance with maintenance procedures in section 3 or 4 . HYDRAULIC SYSTEM . Perform pressure checkout in accordance with paragraph 2-9 . Dirt or rust inhibits operation of launcher . Launch rail does not raise ...
2-53. lappuse
... ( 1 ) and arresting cable , starting at rocket - end , onto a suitable vehicle . t . Return to maintenance work area for cleaning and repacking . 2-17 . REMOVAL OF LINEAR DEMOLITION CHARGE CONTAINER . 4. 2-53 TM 9-1375-215-14 & P.
... ( 1 ) and arresting cable , starting at rocket - end , onto a suitable vehicle . t . Return to maintenance work area for cleaning and repacking . 2-17 . REMOVAL OF LINEAR DEMOLITION CHARGE CONTAINER . 4. 2-53 TM 9-1375-215-14 & P.
2-55. lappuse
... clean protective nylon cover and place in storage container . k . Clean , roll up , and return 75 - ft ( 22.9 - m ) special purpose cable to storage container . I. Using adjustable or 1-1 / 8 inch wrench , loosen turnbuckle locknuts ( 7 ) ...
... clean protective nylon cover and place in storage container . k . Clean , roll up , and return 75 - ft ( 22.9 - m ) special purpose cable to storage container . I. Using adjustable or 1-1 / 8 inch wrench , loosen turnbuckle locknuts ( 7 ) ...
2-59. lappuse
... Clean and oil U - bolts and nuts and place in plastic or barrier bag before extended storage . f . Remove four U - bolts ( 5 ) and stow in storage container . g . Remove lifting sling ( 6 ) from storage container . h . i . Place lifting ...
... Clean and oil U - bolts and nuts and place in plastic or barrier bag before extended storage . f . Remove four U - bolts ( 5 ) and stow in storage container . g . Remove lifting sling ( 6 ) from storage container . h . i . Place lifting ...
2-62. lappuse
... clean all moving parts , using compressed air , steam , etc. , as needed . Disassemble launch rail supports , if necessary , to remove accumulated dirt . Perform PMCS lubrication ( Table 2-1 , page 2-8 ) immediately after cleaning . 1 ...
... clean all moving parts , using compressed air , steam , etc. , as needed . Disassemble launch rail supports , if necessary , to remove accumulated dirt . Perform PMCS lubrication ( Table 2-1 , page 2-8 ) immediately after cleaning . 1 ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew