Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 15.
2-25. lappuse
... tighten all four turnbuckles . s . Using 1-1 / 8 inch or adjustable wrench , tighten locknuts ( 9 ) . 2-11 . LOADING LINEAR DEMOLITION CHARGE CONTAINER ON LAUNCHER . 0. Remove turnbuckles from storage container . 2-25 TM 9-1375-215-14 & P.
... tighten all four turnbuckles . s . Using 1-1 / 8 inch or adjustable wrench , tighten locknuts ( 9 ) . 2-11 . LOADING LINEAR DEMOLITION CHARGE CONTAINER ON LAUNCHER . 0. Remove turnbuckles from storage container . 2-25 TM 9-1375-215-14 & P.
2-30. lappuse
... adjustable wrenches authorized in RPSTL will be needed for this operation . a . Release detents ( 1 ) by pushing up on levers . b . Remove ball - lock pins ( 4 ) . NOTE The 10 ° clinometer reading assumes item is on level ground ...
... adjustable wrenches authorized in RPSTL will be needed for this operation . a . Release detents ( 1 ) by pushing up on levers . b . Remove ball - lock pins ( 4 ) . NOTE The 10 ° clinometer reading assumes item is on level ground ...
2-36. lappuse
... adjustable open - end wrenches , remove bolt ( 9 ) and nut ( 10 ) from rocket harness connector ( 11 ) . NOTE Ensure that bridle cable is not twisted . 7 ai . Slip rocket bridle cable loop ( 12 ) 2-36 TM 9-1375-215-14 & P.
... adjustable open - end wrenches , remove bolt ( 9 ) and nut ( 10 ) from rocket harness connector ( 11 ) . NOTE Ensure that bridle cable is not twisted . 7 ai . Slip rocket bridle cable loop ( 12 ) 2-36 TM 9-1375-215-14 & P.
2-37. lappuse
... adjustable open - end wrenches , tighten nut ( 10 ) onto bolt ( 9 ) . • CAUTIONS Ensure rocket harness connector ( 11 ) is pointed forward and positioned near front of linear demoli- tion charge container . Ensure that shock cords at ...
... adjustable open - end wrenches , tighten nut ( 10 ) onto bolt ( 9 ) . • CAUTIONS Ensure rocket harness connector ( 11 ) is pointed forward and positioned near front of linear demoli- tion charge container . Ensure that shock cords at ...
2-51. lappuse
... adjustable wrenches authorized in RPSTL will be needed for this operation . 7 permont pady in 3 8 2 4 a . 1 Disconnect linear charge electrical lead ( 1 ) from receptacle No. 2 ( 2 ) and replace protec- tive cap on receptacle No. 2 . b ...
... adjustable wrenches authorized in RPSTL will be needed for this operation . 7 permont pady in 3 8 2 4 a . 1 Disconnect linear charge electrical lead ( 1 ) from receptacle No. 2 ( 2 ) and replace protec- tive cap on receptacle No. 2 . b ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew