Operator's, Unit, Intermediate Direct Support, and Intermediate General Maintenance Manual Including Repair Parts and Special Tools List: Demolition Kit, Mine Clearing Line Charge (MICLIC).Headquarters, Department of the Army, 1986 |
No grāmatas satura
1.–5. rezultāts no 46.
1-3. lappuse
... place . It has a hydraulically - elevated launcher rail and primarily consists of launcher rail , support and frame weldment assembly , safety switch electrical assembly and hydraulic assembly . Support equipment stored in the storage ...
... place . It has a hydraulically - elevated launcher rail and primarily consists of launcher rail , support and frame weldment assembly , safety switch electrical assembly and hydraulic assembly . Support equipment stored in the storage ...
1-4. lappuse
... places the ends of the detonating cord core next to the fuze's detonators . The ar- resting cable half of the fuze connector allows electrical and mechanical connec- tions to the fuze . The linear demolition charge and fuze are secured ...
... places the ends of the detonating cord core next to the fuze's detonators . The ar- resting cable half of the fuze connector allows electrical and mechanical connec- tions to the fuze . The linear demolition charge and fuze are secured ...
1-13. lappuse
... place by artillery fire , ( combat ) , or range control / EOD ( training ) . ( 9 ) Report malfunction in accordance with AR 75-1 . 1-11 . Section III . TECHNICAL PRINCIPLES OF OPERATION GENERAL . This section describes the operation of ...
... place by artillery fire , ( combat ) , or range control / EOD ( training ) . ( 9 ) Report malfunction in accordance with AR 75-1 . 1-11 . Section III . TECHNICAL PRINCIPLES OF OPERATION GENERAL . This section describes the operation of ...
2-18. lappuse
... lock pins ( 4 ) from launcher rail supports ( 5 ) . V. Move ball - lock pins ( 4 ) to the LOCK position . w . Place detents in down position . 2-10 . INSTALLING LAUNCHER ON TRAILER . 3 10 12 2-18 TM 9-1375-215-14 & P.
... lock pins ( 4 ) from launcher rail supports ( 5 ) . V. Move ball - lock pins ( 4 ) to the LOCK position . w . Place detents in down position . 2-10 . INSTALLING LAUNCHER ON TRAILER . 3 10 12 2-18 TM 9-1375-215-14 & P.
2-20. lappuse
... Place lifting sling ( 6 ) on launcher ( 7 ) with long axis parallel to long axis of launcher ( 7 ) . h . Hook four snap hooks ( 8 ) to four lifting rings ( 9 ) . WARNING Do not allow launcher to sway during installation to avoid injury ...
... Place lifting sling ( 6 ) on launcher ( 7 ) with long axis parallel to long axis of launcher ( 7 ) . h . Hook four snap hooks ( 8 ) to four lifting rings ( 9 ) . WARNING Do not allow launcher to sway during installation to avoid injury ...
Citi izdevumi - Skatīt visu
Bieži izmantoti vārdi un frāzes
9/16-inch combination box appendix F arresting cable fuze B-nut Bleed Hydraulic System bridle cable cable fuze connector check valve clevis pins clinometer column CONT control valve handle control valve lever cotter pin damage demolition charge container detent assembly detonators Disconnect elbow electrical lead Ensure flatwashers fluid dampener hand knobs hand pump hex key hex nuts hook hydraulic control valve hydraulic cylinder hydraulic fluid hydraulic hose INITIAL SETUP Tools inserting ball-lock pins Inspect Install intermediate direct support item 12 lanyard launch launcher rail supports lifting sling linear charge linear demolition charge lockwashers M34 blasting machine maintenance Materials/Parts mechanic's tool MICLIC open-end wrench operation paint PAOZZ personnel PMCS PROCEDURES protective cap Pull pump handle rear receptacle RELEASE position release valve handle repacked repair rocket bands rocket motor safety switch assembly Screw socket wrench storage container street elbow task covers tighten tool kit item Tools General mechanic's towing vehicle U-bolts Unscrew