Operator, Organizational, Direct Support, and General Support Maintenance Manual (including Repair Parts and Special Tools List) for Alinement Device, M139 (4931-01-048-5834) and Alinement Device with Case, M140 (4931-01-187-9713).Headquarters, Department of the Army, 1991 |
No grāmatas satura
1.–5. rezultāts no 7.
5-3. lappuse
... SURFACE Check that mounting surface is clean and free of nicks and burrs . DECALS , INSTRUCTION AND IDENTIFICATION PLATES Check that plates are present and readable . Note CAP ASSEMBLY LENS CELL Place instrument in a dark area ...
... SURFACE Check that mounting surface is clean and free of nicks and burrs . DECALS , INSTRUCTION AND IDENTIFICATION PLATES Check that plates are present and readable . Note CAP ASSEMBLY LENS CELL Place instrument in a dark area ...
5-4. lappuse
... SURFACE Base does not seat properly .. SYMPTOM INDEX OPTICS Lens fogged or condensation present . No illumination .... Illuminated , but no reticle pattern Troubleshooting Procedure ( Page ) 5-5 5-5 5-5 .. 5-6 5-3 GENERAL CONTINUED ...
... SURFACE Base does not seat properly .. SYMPTOM INDEX OPTICS Lens fogged or condensation present . No illumination .... Illuminated , but no reticle pattern Troubleshooting Procedure ( Page ) 5-5 5-5 5-5 .. 5-6 5-3 GENERAL CONTINUED ...
5-5. lappuse
... SURFACE 1. BASE ( 1 ) DOES NOT SEAT PROPERLY Observe visually . a . Remove nicks and burrs with file . b . Replace lever ( p 5-8 ) . OPTICS 2. LENS ( 2 ) FOGGED OR CONDENSATION PRESENT Check for broken lens or damaged or missing parts ...
... SURFACE 1. BASE ( 1 ) DOES NOT SEAT PROPERLY Observe visually . a . Remove nicks and burrs with file . b . Replace lever ( p 5-8 ) . OPTICS 2. LENS ( 2 ) FOGGED OR CONDENSATION PRESENT Check for broken lens or damaged or missing parts ...
5-19. lappuse
... surface only enough to assure a burr - free surface . A Using sharpening stone ( Item 9 , Appendix D ) , remove any burred or raised edges from surfaces ( 1 ) . B Install collimation standard ( 2 ) to base ( 3 ) by alining pin ( 4 ) to ...
... surface only enough to assure a burr - free surface . A Using sharpening stone ( Item 9 , Appendix D ) , remove any burred or raised edges from surfaces ( 1 ) . B Install collimation standard ( 2 ) to base ( 3 ) by alining pin ( 4 ) to ...
5-20. lappuse
... surfaces ( 8 ) is parallel to locating dovetail ( 9 ) . E Install three screws ( 10 ) , tighten lightly . 2 12 11 Note • Use two V - blocks when setting up M139 standard . • Dowel pins are matched and should not be separated . F Set ...
... surfaces ( 8 ) is parallel to locating dovetail ( 9 ) . E Install three screws ( 10 ) , tighten lightly . 2 12 11 Note • Use two V - blocks when setting up M139 standard . • Dowel pins are matched and should not be separated . F Set ...
Bieži izmantoti vārdi un frāzes
3rd position 5-8 COLLIMATION ALINEMENT DEVICE MAINTENANCE AMSMC-MAS ROCK ISLAND Army Armament AZIMUTH TEST FIXTURE BORESIGHT BUSINESS REPLY MAIL C-3 EXPLANATION cap assembly Centimeters CHEMICAL COMMAND ATTN COLLIMATION AND INSPECTION collimation standard collimator 9 COLUMNS SECTION components Depot Maintenance DESCRIPTION AND USABLE DEVICE MAINTENANCE INSTRUCTIONS dial indicator Disassembly dovetail END OF FIGURE EXPLANATION OF COLUMNS Field Maintenance Fluid Ounces infinity collimator Install Instrument and Fire item number Kilopascals M139/M140 ALINEMENT DEVICE M139& Alinement M140 Alinement Device maintenance code maintenance function MAINTENANCE INSTRUCTIONS CONTINUED Maintenance Manual Maintenance Repair Materials/Parts Materiel Meters MUNITIONS AND CHEMICAL National Stock Number NUMBER INDEX Objective Cell Assembly objective lens OPTICAL CELL ASSEMBLY packing PAHZZ PAOZZ plate projector collimator Reassembly Remove Replace retaining ring Reticle Cell Assembly screws sealing compound Item Self-Propelled sharpening stone Short Tons SMR code source code Special Tools List spot seal Support Maintenance tritium troubleshooting U.S. Army USABLE ON CODES V-block